TOUGH-SEAL™ 32

TOUGH-SEAL™ 32 is a tough and durable fast gelling Potting Compound and Sealant with excellent Thermal Cycling Stability.

TOUGH-SEAL™ 32 Properties

tough-seal label design
  • Long working time
  • Low viscosity
  • 450% elongation
  • Shore Hardness: 40A
  • Excellent Thermal Cycling Stability from -40°F (-40°C) to 302°F (150°C)
  • Applications include: helideck lighting, electronic sensors, LED Lighting, automotive sensors, marine lighting

Product Specifications: PC2032AB

TOUGH-SEAL™ 32 is a tough and durable fast gelling Potting Compound and Sealant with excellent Thermal Cycling Stability. This low viscosity material is self-leveling and flows like maple syrup around intricate electrical components to ensure complete coverage of your entire PCB or electronic assembly.

TOUGH-SEAL™ 32 has a longer 60 minute working time and a Shore Hardness of 40A, which is similar to the hardness of a pencil eraser. TOUGH-SEAL™ 32 reaches 94% of its full hardness after an overnight cure or with a heat cure of 1 hour at 80°C (176°F). TOUGH-SEAL™ does not exotherm or shrink during curing, therefore there is no embedment stress induced on the electronic components that could cause damage and failure of the PCB or electronic assemblies. Sensitive electronics can be potted safely with low embedment stress TOUGH-SEAL™.

With a high elongation of 450% when fully cured, TOUGH-SEAL™ 32 maintains exceptional flexibility and thermal cycling stability from –40°C to 150°C (-40°F to 302°F) without pulling back, wilting, or cracking. This ensures a tough seal that will stop moisture or other contaminants from damaging sensitive PCB’s and electronics.

TOUGH-SEAL™ has very aggressive adhesion to aluminum, making it a perfect choice for potting aluminum housings in LED lighting applications. TOUGH-SEAL™ bonds extremely well with most polymers. For housing and wire insulation materials that are exceptionally difficult to bond to, we offer our KEY PR1200 PRIMER, an aggressive adhesive promoter that is simple to use.

Technical Data Sheet (TDS) and Safety Data Sheet (MSDS)

Tough-Seal Series

Physical Properties
32

Color, Part A

Off White

Viscosity at 25°C, cP, Part A, (RVT #5, 20 RPM)

4,500

Specific Gravityat 25°C, Part A

1.15

Color, Part B

Black

Viscosity at 25°C, cP, Part B, (RVT #5, 20 RPM)

7,000

Specific Gravity at 25°C, Part B
1.02
Density at 25°C, lbs/gal, Part B
8.5
Color, Mix
Grey / Black
Viscosity at 25°C, cP, Mix, (RVT #5, 20 RPM)
6,000
Specific Gravity at 25°C, Mix
1.07
Density at 25°C, lbs/gal, Mix
8.9
Mix Ratio by Volume
1A to 2B
Mix Ratio by Weight
57A to 100B
Gel Time at 25°C, Minutes, 100 grams
60
Shelf Life, Ambient, Part A Bulk (15°C to 35°C)
12 Months
Shelf Life, Ambient, Part B Bulk (15°C to 35°C)
12 Months
Shelf Life, Cold, Part A Bulk (-18°C to 3°C)
12 Months
Shelf Life, Cold, Part B Bulk (-18°C to 3°C)
12 Months
Electrical & Thermal Properties
32
Dielectric Strength, 25°C, Volts/mil
350
Volume Resistivity, 25°C, Ohm-cm x (10)12
1.75
Dielectric Constant, 25°C – 1 MHz
4.85
Dielectric Constant, 25°C – 1 kHz
4.85
Dielectric Constant, 25°C – 60 Hz
5.45
Dissipation Factor, 25°C – 1 MHz
0.025
Dissipation Factor, 25°C – 1 kHz
0.021
Dissipation Factor, 25°C – 60 Hz
0.043
Heat Capacity Cp, 25°C, J/g°K
1.80
Thermal Conductivity, 25°C, W/m°K
0.20
Coefficient of Thermal Expansion, ppm/°C
(-) 65°C to 75°C
200
75°C to 100°C
200
100°C to 150°C
200
Coefficient of Thermal Expansion, ppm/°F
(-) 85°F to 167°F
111
167°F to 212°F
111
212°F to 302°F
111
Click to View Chart
Hardness vs Temperature
32
(-75°C / -103°F)
84 A
(-25°C / -13°F)
48 A
5°C / 41°F
43 A
25°C / 77°F
40 A
50°C / 122°F
41 A
66°C / 150°F
42 A
80°C / 176°F
42 A
100°C / 212°F
42 A
120°C / 248°F
41 A
150°C / 302°F
39 A
Click to View Chart
Hardness vs Ambient Cure Time
32
1 Hour
0 A
2 Hours
0 A
4 Hours
0 A
8 Hours
0 A
12 Hours
0 A
1 Day
9 A
2 Days
23 A
3 Hours
28 A
4 Hours
31 A
1 Week
35 A
1 Month
43 A
Click to View Chart
Mechanical Properties
32
Tensile Strength per ASTM D638, 25°C, PSI
850
Elongation per ASTM D638, Type I, 0.125 in, 25°C
450%
Tensile Lap Shear Strength - per ASTM D1002, 25°C, psi *
Aluminum Bare
480 Co
Steel Bare
200 Ad
Steel Ground
200 Ad
Primed Steel
200 Ad
Galvanized Steel
200 Ad
Tin Plated Steel
200 Ad
Chrome Plated Steel
200 Ad
Tensile Lap Shear Strength - per ASTM D3163, 25°C, psi **
FRP – Polyester Fiberglass
210 Ad
Garolite G-9 Melamine/Glass
220 Ad
Garolite G-10 Epoxy/Glass
360 Ad
Garolite XX Phenolic/Paper
160 Ad
Tensile Lap Shear Strength - per ASTM D3163, 25°C, psi **
Acrylic
300 Ad
Acrylic/PVC
250 Ad
PVC – Polyvinyl Chloride
250 Ad
CPVC – Chlorinated PVC
280 Ad
ABS – Acylonitrile Butadiene Styrene
180 Ad
PETG – Polyethylene Terephthalate
220 Ad
Lexan – Polycarbonate
210 Ad
Nylon 6/6 – Polyamide
260 Ad
Polypropylene
40 Ad
Polyethylene LDPE
10 Ad
Polyethylene HDPE
20 Ad
Teflon PTFE – Polytetrafluoroethylene
20 Ad
Noryl – Polyphenylene Oxide/Polystyrene
150 Ad
Ultem Polyetherimide
170 Ad

Which TOUGH-SEAL™ is Right for you?

TOUGH-SEAL™ is a superior family of KEY sealants available in four standard formulations to fit a variety of potting applications. While all TOUGH-SEAL™ formulations are durable hybrid epoxy elastomers that grip and protect under the most aggressive conditions, they are available in a combination of properties that vary in hardness, gel-time, working time, and flow.

Order Your TOUGH-SEAL™ Evaluation Kit Today!

Your Evaluation Kit will include everything you need to perform your own high quality product evaluation for your application.

Ready To Talk to Us?

TOUGH-SEAL™ PC is bulldog tough and bred to grip and protect, under the most aggressive conditions.


Contact us for help selecting the correct TOUGH-SEAL™ PC for YOUR application!